– It has a basic PVC conveyor belt with a width of 90 and a length of 350 cm
– With a secondary PVC conveyor belt with a width of 90 and a length of 200 cm
– With a PVC inclined conveyor belt with a width of 90 and a length of 200 cm
– It has a PVC conveyor belt before sewing, each 200 cm long and 90 cm wide.
– It has a PVC conveyor belt after sewing, each 200 cm long and 90 cm wide.
– It has a can type tunnel conveyor and a double-wing chain with fireproof epoxy coating, approximately 400 cm long and 85 cm wide.
– With a pulley support of the feeding conveyor to center the product on the primary conveyor
– It has two roll holder systems in order to place two bubble plastic rolls on the device, one of which is used as a reserve roll.
– It has grooved driving drums to open the bubble plastic roll
– It has pneumatic drums for easy replacement of the bubble plastic roll or its release
– It has a sewing system connecting the bubble storage roll to the completed roll for easy operation and increasing the speed of changing the roll as thermal sewing.
– It has a pneumatic system for an easier initial passage of the bubble roll by the operator
– It has a pneumatic mechanical cutter system for the bubble roll using a steel blade
– It has a pneumatic sewing system with a replaceable blade sewing with fireproof coating made of industrial teflon with a length of approximately 90 cm for polyethylene plastic.
– It has a sewing system from below to prevent the wear and tear of the wiring part of the device
– It has a spiral system for uniformity and air circulation inside the tunnel along with 2 fan packs
– It has a cooling fan system using 4 blower fans at the top of the end of the tunnel
– It has a cooling fan system using 1 blower under the tunnel
– It has a pneumatic panel system with related accessories for sewing and cutting bubble and polyethylene parts separately.
– It has an automatic up and down roll opening system for polyethylene plastic
– It has an upper and lower storage roll system for polyethylene plastic
– It has a 200 cm long inclined roller table system at the end
– With a system of end rollers of the tunnel
– Has Iran radiator RAN25 gas torch
– Electrostatic painting
-Silicone screen to prevent energy loss at the beginning and end of the tunnel
– Isolation 4 inch pshm snag and any hookah
– Easy to install and make a movie roll
– Valves for adjusting the height of the entrance and exit of the tunnel
– Quick replacement of thermal elements from outside the tunnel
– Complete piping inside the tunnel for the passage of wires and cables
-Adjustment of hot air blowers inside the tunnel
– The ability to move the device with a rotating wheel and install it with fixed bases in a specific position
– The need for an operator to change the shrink film rolls (top and bottom) when the roll is finished and monitor the operation of the machine
– Input device directly
– The optimal temperature of the tunnel to prevent the wear of the machine parts is 200 degrees Celsius
Combustion chamber with special fireproof sheet
– Has 2 separate electrical panels with electrical accessories for bubble and shrink parts
– With 9 single-phase to three-phase inverters to control the speed of asynchronous motors
– It has 2 industrial controllers of mini type to control the performance of the bubble and shrink part
-Having 2 DC power supply units to supply direct power to the control circuit and sensors
– With optical mirror sensors for device automation
– It has inductive proximity sensors for device automation
– It has a magnetic sensor on the jack for device automation
– It has a bubble plastic sewing system for the storage part of the roll
– It has trans stitching to protect the operator against the risk of electrocution for the bubbly and shrink parts separately
– It has a polyethylene sewing temperature adjustment system as PID control using SSR
-Phase control to control voltage fluctuations and phase sequence
-Miniature mechanical and electronic relays
– Miniature fuses, thermal switches and fuse insulators
LN-45AS350EG radiator packing line
With PLC, HMI and INVERTER for all electric motors and single-phase power consumption, with electric panel and pneumatic panel with pusher system, transmission, stretch screw, loading with printer, ejector, tilt back (reverse), special hydraulic system, with warning system in special situations, film cutting system At the end of the operation, the ability to automatically adjust the amount of stretch film coverage on the product, with the initial and final feeders, with the ability to stretch the stretch film around the product in a completely uniform manner without loosening the electrostatic paint, without vibration and creating additional sounds, with low wear and tear and a great structure Durable, able to work around the clock, with a special system to maintain the product while moving into the tunnel, with a manual including the steps and methods of maintenance, repairs, troubleshooting, and a list of spare parts and an electrical map of electrical and mechanical consumables and parts (electromotor and gearboxes) and high-quality pneumatics with 2-year warranty and 10-year after-sales service
توان مصرفی |
380v/3PH+N+PE/50HZ, 60KW |
---|---|
هوای مصرفی |
200 liters per minute, 6 to 8 times |
سرعت کارکرد |
150 to 360 packages per hour |
فیلم مصرفی |
25 to 30 microns thick, Diameter 20 cm, LLDPE stretch film 300%, Normal stretch nylon, Width 50 cm |
ابعاد دستگاه (ارتفاع - عرض - طول) به میلیمتر |
220*220*1800 |
وزن دستگاه |
About 1600 kg |
Product weight |
5 to 60 kg |
دهانه تونل |
The width of the opening is 90 cm |
طول تیغه دوخت |
90 cm |
گاز مصرفی |
1/4 pound per square inch, 7 to 14 cubic meters per hour |